Frequently asked questions

Cost depends on floor size, condition and coating type. We provide affordable custom quotes for every project.

Most commercial epoxy floors are completed in 1 to 3 days depending on surface size and preparation. Full curing takes 24 to 72 hours before heavy use.

Yes. Cracks and surface damage are repaired before the epoxy is applied, and the slab is cleaned and ground so the coating bonds properly.

Yes, it is ideal for garages due to its strength, stain resistance and easy cleaning.

Yes, it is highly resistant to oils, chemicals, acids, and industrial spills.

Regular sweeping and mopping is enough to keep epoxy floors clean and long-lasting.

Both. From interior walls to exterior surfaces, the work covers the whole property, with clean lines and smooth finishes as the standard we hold ourselves to.

Offices, retail stores and larger commercial facilities. The specification changes with the building, so we tailor the solution to the space rather than applying one approach everywhere.

That is how we prefer to run it. We understand the importance of minimizing disruption, so we sequence the work to keep the space usable while it is under way.

High-quality paints and coatings that give long-lasting protection against wear, weather and daily use. What goes on a given surface depends on where it is and what it has to take.

Cracks, chips, holes, spalled edges and worn surface areas. Concrete floors develop all of these over time from heavy foot traffic, impact and environmental conditions.

Usually not. Most floors that look finished are worn and damaged at the surface rather than structurally gone, and repair restores strength and appearance without the demolition and downtime a replacement involves.

That is the most common reason to book this work. Repair first, coat second. A coating cannot bridge a fault that is still moving underneath it.

Repairs are ground flush and blended in, and a coating or polished finish on top makes them harder still to pick out. On a bare slab left uncoated, a color difference can remain.

Yes. We take on small residential repairs and larger industrial and commercial projects, and both get the same assessment and the same materials.

It depends on how much of the floor is affected and what has to cure before the next step. We give you the sequence and the timing after the assessment, not before it.

Restoration is built for exactly that situation. We repair cracks, resurface damaged areas and remove stains in place, so the floor goes back into service without the cost of complete replacement.

Heavy traffic, spills and age. Over time those leave cracks, stains and surface imperfections that affect how the floor performs as well as how it looks.

We begin by assessing the condition of the floor, then select the repair and resurfacing methods that suit what the slab actually needs.

Once repairs are complete we can polish, stain or coat the surface to improve its appearance and durability. Which one suits best depends on the space and how the floor is used.

Grinding creates a smooth, even base and improves adhesion, so the new coating bonds to sound concrete rather than to whatever was left on top of it. The same preparation is used ahead of polished concrete and other floor treatments.

Yes. Grinding removes leftover adhesive and old coatings, and it levels uneven areas at the same time.

No. It is used on new installations as well as on older floors that need extra attention before they can be finished.

We use specialized grinding machinery, matched to the size of the area and to the finish the floor is being prepared for.

That is where it does its best work. Polished concrete floors are durable, resistant to stains and easy to clean, which is what makes them a common choice for areas that see constant use.

It can. Polishing produces a smooth, mirror-like surface that reflects light, so a space with the same lighting reads as brighter once the floor is finished.

Offices, showrooms and homes, along with commercial and industrial spaces. Anywhere an existing slab should look better without a covering being laid over it.

Little. The finished surface is easy to clean and resists staining, which is the main reason people choose polishing over a floor covering.

Small steel shot is propelled at the floor at high velocity. It cleans the concrete and profiles it at the same time, lifting dirt, old coatings and contaminants out of the surface.

It is a dust-controlled process, which is a large part of why it is used indoors and in working environments where an open grinding operation would be a problem.

Blasting leaves a roughened texture, and that texture is what a new coating such as epoxy or paint keys into. Adhesion is decided at this stage, not at the coating stage.

Industrial and commercial environments where correct surface preparation decides how long the finished floor lasts, whether the project is a new flooring system or the restoration of an existing one.

They are flakes of colored material broadcast into an epoxy floor while the coating is still wet. The chips become part of the system and are sealed under a clear topcoat.

They help. The chip texture breaks up an otherwise smooth surface and improves slip resistance, and a grip additive can be added to the clear coat as well.

Yes. Chips come in a wide range of color schemes, so a floor can be matched to existing decor or blended into something entirely its own.

No. The same system is used in commercial showrooms, finished basements, retail spaces and warehouses. The blend is what changes between a showroom and a shop floor.

No. The chips are sealed under the topcoat, so the surface you clean is the same seamless coating you would clean on a plain epoxy floor.

A chip system is applied as part of a coating installation, so an existing floor is prepared and recoated rather than dusted with chips. We will tell you at the walkthrough whether the slab suits it.

Anywhere concrete takes daily punishment. Garages, basements, commercial showrooms, warehouses and industrial floors are the most common jobs we coat in Sterling Heights and across Metro Detroit.

Yes. Proper surface preparation is what gives a coating its adhesion and its lifespan. We grind or shot blast every floor before coating it, and we repair cracks and holes at the same stage.

Usually. Old stains, wear and minor damage are dealt with during preparation and repair. A slab has to be structurally sound, and the walkthrough is where we tell you if it is not.

It depends on the size of the floor, the condition of the concrete and the system you choose. We quote each job after seeing it, and the quote is free with no obligation.

A grip additive or a chip blend can be worked into the system where traction matters. Tell us how the space is used and we will specify the finish to match.

The medium-duty and heavy-duty epoxy options we install carry a five-year workmanship warranty.

Warehouses, factories, laboratories and showrooms are the most common. If the floor is concrete and the building works for a living, an epoxy system is usually a candidate.

Yes. We phase the work by area and agree the sequence with you in advance, which is how a live building keeps running while its floor is replaced.

It is a common choice where hygiene matters, because the surface is seamless and has no joints or grout lines for residue to collect in. It cleans down rather than being scrubbed out.

Sometimes, and sometimes the old finish has to come off first. We test the existing coating during the survey. Where removal is needed, that is a service we provide as well.

The condition of the concrete is checked at the survey stage and preparation is matched to what we find. Coating a slab without dealing with what is in it is how a new floor fails early.

Color changes between areas can be built into the installation, so aisles, work cells and walkways read differently underfoot. Tell us the layout and we will include it in the specification.

The aim is the opposite. We remove existing layers of epoxy, paint or other coatings without damaging the underlying concrete, using equipment matched to what is being taken off.

Because the new system would only be as sound as what it sits on. Proper removal is what makes strong adhesion and long-term performance possible for the floor that follows.

Epoxy, paint and other floor coatings. We look at what is down and how well it is still bonded before choosing the method.

We work for efficiency and precision so downtime is kept down, and we plan the sequence around how the space is used, whether that is a residential garage, a commercial unit or an industrial facility.

That is what the system is specified for. We install coatings intended for daily vehicle use, which is a different specification from a decorative floor that never sees a car.

Usually not. Degreasing, grinding and crack repair are part of the job, and many garage floors that look past saving are dirty and worn rather than structurally gone. The walkthrough is where we confirm which one yours is.

Foot traffic comes back before vehicles do. The exact wait depends on the system and the temperature, so we confirm the timeline with you before the work starts rather than guessing on the day.

A plain coating is one color. A flake finish broadcasts decorative chips into the coating, which adds texture, traction and depth. Both are sealed under the same protective topcoat.

Most often because the concrete was not prepared. Coating over a sealed, oily or unground slab leaves the film with nothing to bond to. Grinding and decontamination are not optional steps for us.

Yes, for light commercial use. Service bays, fleet parking and shop floors are all within scope. Heavy production environments are covered on our industrial epoxy flooring page.

Factories, warehouses and production facilities. Anywhere the floor is part of the plant rather than just the surface people walk on.

That depends on the area, the system and how the building runs, so it is planned rather than guessed. The work is installed area by area and we agree the windows with you before we start rather than discovering them on site.

That is what a high-build industrial system is for. We match the build to the equipment and the loading in each area, so a busy loading aisle gets a different specification from a storage bay.

Tell us what is used in the space. Industrial epoxy is chosen for resistance to the chemicals actually present, and the right answer for a machine shop is not the right answer for a plating line.

Thermal movement and washdown are part of the specification conversation. Different systems tolerate different conditions, so we ask about it up front rather than assuming a standard floor will cope.

Yes. Phasing by area is the normal approach in a live plant, and it lets production continue while the floor is replaced section by section.

Corrosion, chemicals, moisture and extreme conditions. The coating is chosen for the environment the surface actually lives in, which is what separates industrial work from decorative painting.

Structures, equipment and surfaces across factories and warehouses, including heavy machinery. Each project is matched to its own requirements rather than to a standard package.

Preparation and precise application are what decide the result. A high-performance coating on a poorly prepared surface fails at the bond line, so every step is handled with care before anything is applied.

Yes. Alongside protection, the coatings improve the overall appearance of a facility and contribute to how safe it is to work in.

Polished concrete is your existing slab mechanically refined and hardened. An epoxy floor is a new coating applied on top of the slab. One changes the concrete, the other covers it.

Contemporary homes, offices, showrooms and industrial buildings all use it. It is a common choice wherever a floor needs to look finished and still take traffic.

Very little. Regular dust mopping and damp mopping keeps a polished floor looking right, which is a large part of why it works out cost-effective.

Most can, but the slab has to be sound and thick enough for the surface to be cut back. We assess the concrete first and tell you honestly if polishing is the wrong answer for it.

A clean, dry polished floor gives reasonable traction. Like any hard surface it is slick when wet, so we will talk through traction treatments if the space sees spills.

You choose the level. The polishing steps run from a low satin sheen up to a high reflective gloss, and we stop the sequence where you want it.

The published range is roughly $4 to $10 per square foot depending on the condition of the surface, the size of the area and the coating type. We confirm it after seeing the slab.

Typically one to three days on site. Full cure takes another 24 to 72 hours before heavy use, and cold weather lengthens that rather than shortening it.

Yes. Cracks and surface damage are repaired as part of the preparation, before any coating goes down.

Surface preparation, then repairs, then a primer or base coat, then the epoxy layer, then a protective top coat. The list below sets each stage out in order.

It is highly durable and resistant to chemicals, stains, impact and heavy traffic once it has fully cured.

Cost depends on floor size, condition and coating type. We quote each project after we have seen the slab.

Most commercial epoxy floors are completed in one to three days, depending on the size of the area and how much preparation the slab needs.

Yes. It is well suited to garages because of its strength, stain resistance and easy cleaning.

Yes, it can be applied over properly prepared concrete for a smooth and strong finish.

Regular sweeping and mopping is enough to keep an epoxy floor clean and long lasting.

A durable floor coating that finishes concrete in colors, patterns and effects rather than leaving it gray. Metallic pours, chip broadcasts and tinted quartz all fall under the same heading.

Homes, garages, basements, showrooms and commercial spaces where the floor is part of how the room looks, not only what it has to survive.

It gives you durability, easy maintenance and stain resistance while changing the appearance of the room, which few other flooring choices do at once.

The published range is roughly $5 to $12 per square foot depending on the design and the condition of the surface. A metallic pour costs more than a single-color coat because it takes longer and is less forgiving.

Yes. It is long lasting and resistant to wear, stains, moisture and daily traffic, and it is repairable in place if it is damaged.

It is long lasting, easy to clean, and resistant to stains, moisture and daily wear.

It works well in garages, basements, kitchens and other high-traffic areas of a home.

The published range for residential epoxy flooring is roughly $5 to $8 per square foot depending on the condition of the floor and the finish chosen, which puts a typical garage somewhere between $2,000 and $6,000. We confirm the figure after seeing the slab, because the preparation is what moves the price.

It does not have to be. Anti-slip additives are broadcast into the finish where footing matters, which is standard for a garage that gets wet in winter.

The surface is cleaned and mechanically ground, cracks and pits are repaired, a primer coat is applied, then the epoxy is built up in layers and sealed.

The published range is roughly $4 to $10 per square foot depending on the condition of the slab, the size of the area and the coating system specified. Preparation is the variable that moves it most.

Yes. Epoxy systems resist oils, many chemicals and acids, and industrial spills. The specific resin is chosen against the exposure the floor actually sees, so tell us what gets spilled.

Mainly concrete floors that are clean, dry and properly prepared. Preparation is mechanical, by grinding or shot blasting.

Yes. Damaged sections can be repaired or recoated without replacing the entire floor, provided the surrounding coating is still bonded.

A strong, durable surface that resists heavy traffic, chemicals and wear, and is easier to clean and mark out for safety.